The Journey Begins
- goatram
- Donator 08, 09, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19
- Posts: 1959
- Joined: Wed Apr 09, 2008 11:53 pm
- 16
- Your location: Stanwood, Wa
- Location: Stanwood WA
Re: The Journey Begins
Bait tank coming together. 18' diameter X 28" X 36" tall. Water is 3.5" down from the top. The top is recessed 2" down from the top. There is a 4" lip inside the tank opening to prevent splashing. It is filled by 3/4" pipe from a pump. Drainage will be 1.5" pipe below deck. Collector pipe is 2" should provide head pressure to push the water out the side.
Tested the tank today. Filled it filled with water. Flow was there. Need to do a little more welding on it to close up some of the gaps to increase the current. Dave cut slots in the diamond plate for water flow. Jamie did not weld ever tab but will.
The water flow at the top hole stayed the same as in the picture for 5 minutes.
No to get it back into the shop finishing then on the deck permanently welded in. Not removable. Still need to add the View window at some time. A light needs to be added as well in the bottom
Tested the tank today. Filled it filled with water. Flow was there. Need to do a little more welding on it to close up some of the gaps to increase the current. Dave cut slots in the diamond plate for water flow. Jamie did not weld ever tab but will.
The water flow at the top hole stayed the same as in the picture for 5 minutes.
No to get it back into the shop finishing then on the deck permanently welded in. Not removable. Still need to add the View window at some time. A light needs to be added as well in the bottom
John Risser aka goatram
33' RBW with twin 250 Hondas (Aliens)
2015 Ford F350 Dually
Master of R&D aka Ripoff and Duplicate
33' RBW with twin 250 Hondas (Aliens)
2015 Ford F350 Dually
Master of R&D aka Ripoff and Duplicate
Re: The Journey Begins
This is FIRST CLASS to say the least! It will be interesting to see what all your hours and materials costs are and compare that to a custom built...BIG thing is it is the way you want little if no "settle for's"! It is a pleasure to read your postings. PJ
2009 Raider 185 Pro Fisherman, 2005 90Yamaha, 2012 Yamaha9.9HT, 2008 EzLoader roller, 2004 Dodge TCD dually, 2005/2015 Lance1161
- goatram
- Donator 08, 09, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19
- Posts: 1959
- Joined: Wed Apr 09, 2008 11:53 pm
- 16
- Your location: Stanwood, Wa
- Location: Stanwood WA
Re: The Journey Begins
I will say Capt. My Purse is bleeding Profusely. This week has been Bloody. Ordered from BOE Marine the rest of my Items that I will need. EPRIB Class II from ACR. The Windows Are past the Drawings stage and will be ready for the end of March. Price for 9 windows and a double sliding back door Center front window is hinged at the top. Price will be under $6000. I ordered up Imtra window wash System and switches. I also ordered today the SS264N Duel Thru Hull Transducer
I will be working on the aft deck, Anchor Pulpit, Cuddy Cabin, and Bow railings along with 5 hours of work in the Morning. We shall see how much of my planned work gets accomplishedJohn Risser aka goatram
33' RBW with twin 250 Hondas (Aliens)
2015 Ford F350 Dually
Master of R&D aka Ripoff and Duplicate
33' RBW with twin 250 Hondas (Aliens)
2015 Ford F350 Dually
Master of R&D aka Ripoff and Duplicate
- goatram
- Donator 08, 09, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19
- Posts: 1959
- Joined: Wed Apr 09, 2008 11:53 pm
- 16
- Your location: Stanwood, Wa
- Location: Stanwood WA
Re: The Journey Begins
Saturday Dave aka Fogdocker beat me to my house cause I had to work day shift. We worked on the bow rails. They were formed and located. Also clamped up the anchor pulpit and made supports for the underside of it along with wrapping a 3" strap around it for added strength and to match the Original Work
Sunday the pulpit was tacked on. The topside seams will be TIGed . Worked on getting the cuddy structure ready to welded up. It's done ready for 1" plywood (on order)and the mattress to be made. Need to make a pattern and then cut 2 hatches. for storage under the bed on the port side and the electrical compartment on the Starboard side.
The back deck was welded on some more. It's still not done yet. Need to clean it of all the shavings prior to Tuesday night. I sweetened the pot for the kid doing the welding by adding a Bonus for completion by April.
The back bulkhead was completed by TIGing it up. Looks good.
The anchor bow pulpit railing still needs some elbows formed\bent to tie it into the railing. the Radar Arch and the brow over the front windows are next on the agenda.
This is a fun project. I do keep donating some of my own Blood to the Aluminum Dust that I generate. So far I have gone through 4 10"Carbide tip Saw Blades 3 rolls of .045 wire about 8 lbs of tig rod. and 8 or 10 bottles of argon.
Sunday the pulpit was tacked on. The topside seams will be TIGed . Worked on getting the cuddy structure ready to welded up. It's done ready for 1" plywood (on order)and the mattress to be made. Need to make a pattern and then cut 2 hatches. for storage under the bed on the port side and the electrical compartment on the Starboard side.
The back deck was welded on some more. It's still not done yet. Need to clean it of all the shavings prior to Tuesday night. I sweetened the pot for the kid doing the welding by adding a Bonus for completion by April.
The back bulkhead was completed by TIGing it up. Looks good.
The anchor bow pulpit railing still needs some elbows formed\bent to tie it into the railing. the Radar Arch and the brow over the front windows are next on the agenda.
This is a fun project. I do keep donating some of my own Blood to the Aluminum Dust that I generate. So far I have gone through 4 10"Carbide tip Saw Blades 3 rolls of .045 wire about 8 lbs of tig rod. and 8 or 10 bottles of argon.
- Attachments
-
- 29'build131.jpg (51.45 KiB) Viewed 10797 times
-
- underside showing "T" extrusions
- 29'build138.jpg (79.57 KiB) Viewed 10797 times
-
- 29'build132.jpg (57.19 KiB) Viewed 10797 times
-
- 29'build133.jpg (60.27 KiB) Viewed 10797 times
-
- 29'build134.jpg (49.18 KiB) Viewed 10797 times
-
- 29'build135.jpg (57.07 KiB) Viewed 10797 times
-
- 29'build136.jpg (92.48 KiB) Viewed 10797 times
-
- 29'build137.jpg (103.57 KiB) Viewed 10797 times
John Risser aka goatram
33' RBW with twin 250 Hondas (Aliens)
2015 Ford F350 Dually
Master of R&D aka Ripoff and Duplicate
33' RBW with twin 250 Hondas (Aliens)
2015 Ford F350 Dually
Master of R&D aka Ripoff and Duplicate
Re: The Journey Begins
The bow is really taking shape. I like the concept for your cuddy, gives you headroom inside where needed and it will shed the water if you bury the nose. April...I know you are anxious, but is it realistic? Sure is fun watching this whole build! Again thx for sharing.
2009 Raider 185 Pro Fisherman, 2005 90Yamaha, 2012 Yamaha9.9HT, 2008 EzLoader roller, 2004 Dodge TCD dually, 2005/2015 Lance1161
- goatram
- Donator 08, 09, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19
- Posts: 1959
- Joined: Wed Apr 09, 2008 11:53 pm
- 16
- Your location: Stanwood, Wa
- Location: Stanwood WA
Re: The Journey Begins
Swede aka miles on BD posted this up
Done in red will look cool
Done in red will look cool
- Attachments
-
- Aluminator.jpg (92.46 KiB) Viewed 10767 times
John Risser aka goatram
33' RBW with twin 250 Hondas (Aliens)
2015 Ford F350 Dually
Master of R&D aka Ripoff and Duplicate
33' RBW with twin 250 Hondas (Aliens)
2015 Ford F350 Dually
Master of R&D aka Ripoff and Duplicate
- goatram
- Donator 08, 09, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19
- Posts: 1959
- Joined: Wed Apr 09, 2008 11:53 pm
- 16
- Your location: Stanwood, Wa
- Location: Stanwood WA
Re: The Journey Begins
So I am a little behind in posting should matter much no one is reading it.
The Cuddy Bed was cut and and hinged last weekend. It was shellacked this past Saturday. Today I took it to Churchhill Brothers in Everett WA. for the upholstery.
Last week I bought a new Bostrom Wide Glide II + Serta Seat it took me a day to tear the seat pedestal and adapt the seat to ride on the old Bostrom low pedestal I had and what I set up the seat box for. When I stuck the seat as bought on it and blew up the suspension My head would have hit the ceiling. Did destroy one seat pedestal. The seat that goes on it still needed to be recovered and it was free to me.
The Cuddy Bed was cut and and hinged last weekend. It was shellacked this past Saturday. Today I took it to Churchhill Brothers in Everett WA. for the upholstery.
Last week I bought a new Bostrom Wide Glide II + Serta Seat it took me a day to tear the seat pedestal and adapt the seat to ride on the old Bostrom low pedestal I had and what I set up the seat box for. When I stuck the seat as bought on it and blew up the suspension My head would have hit the ceiling. Did destroy one seat pedestal. The seat that goes on it still needed to be recovered and it was free to me.
- Attachments
-
- 29'build159.jpg (97.96 KiB) Viewed 10729 times
-
- 29'build160.jpg (70.53 KiB) Viewed 10729 times
-
- seat is this one with the same Black and grey color scheme
- WRII.B-G.ULTHR.BC.2ARM.FRONT.jpg (48.51 KiB) Viewed 10729 times
John Risser aka goatram
33' RBW with twin 250 Hondas (Aliens)
2015 Ford F350 Dually
Master of R&D aka Ripoff and Duplicate
33' RBW with twin 250 Hondas (Aliens)
2015 Ford F350 Dually
Master of R&D aka Ripoff and Duplicate
- goatram
- Donator 08, 09, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19
- Posts: 1959
- Joined: Wed Apr 09, 2008 11:53 pm
- 16
- Your location: Stanwood, Wa
- Location: Stanwood WA
Re: The Journey Begins
The plate in the picture is where the Windlass will be mounted.
Santa came late to and left a few packages on the front porch. I should be having a lot of my new toys coming in over the next few days.
Santa came late to and left a few packages on the front porch. I should be having a lot of my new toys coming in over the next few days.
- Attachments
-
- Mount pad for the Windlass
- 29'build161.jpg (48.82 KiB) Viewed 10729 times
-
- BOE Marine supplies. A great deal. with more on the way.
- 29'build162.jpg (51.45 KiB) Viewed 10729 times
John Risser aka goatram
33' RBW with twin 250 Hondas (Aliens)
2015 Ford F350 Dually
Master of R&D aka Ripoff and Duplicate
33' RBW with twin 250 Hondas (Aliens)
2015 Ford F350 Dually
Master of R&D aka Ripoff and Duplicate
- goatram
- Donator 08, 09, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19
- Posts: 1959
- Joined: Wed Apr 09, 2008 11:53 pm
- 16
- Your location: Stanwood, Wa
- Location: Stanwood WA
Re: The Journey Begins
Dave aka FogDocker cutting the two holes thru the 1/2" plate in prep for the windlass to be installed first picture using the Metabo Jig Saw. 4 blades from Bosch pit the dust for the install. Seems to be a rib was in the way for the fwd chain fall hole. He ran me out of blades on Saturday.
The second and third pictures are of the completed windlass that i got from a BD Brotha. Owner of a Clorox bottle Defiance Boat aka deviant.
The second and third pictures are of the completed windlass that i got from a BD Brotha. Owner of a Clorox bottle Defiance Boat aka deviant.
- Attachments
-
- Dave cutting the holes
- 29'build147.jpg (112.4 KiB) Viewed 10727 times
-
- Install done
- 29'build148.jpg (118.45 KiB) Viewed 10727 times
-
- Install done
- 29'build149.jpg (115.19 KiB) Viewed 10727 times
-
- My son
- 29'build150jpg.jpg (108.39 KiB) Viewed 10727 times
John Risser aka goatram
33' RBW with twin 250 Hondas (Aliens)
2015 Ford F350 Dually
Master of R&D aka Ripoff and Duplicate
33' RBW with twin 250 Hondas (Aliens)
2015 Ford F350 Dually
Master of R&D aka Ripoff and Duplicate
- spoiled one
- Donator '08 '09 '10
- Posts: 1138
- Joined: Mon Jan 14, 2008 4:48 pm
- 16
- Your location: Anchorage, Alaska
- Location: Anchorage, Alaska
Re: The Journey Begins
You will love that Bostrom seat, John. Very comfortable. I like the bow pulpit. It really adds to the look of the bow. How long and wide is the cuddy?
Keep the pictures coming!
Keep the pictures coming!
Spending my kids inheritance with them, one adventure at a time.
2010 AK Meet & Greet
2012 AK Meet and Greet
2010 AK Meet & Greet
2012 AK Meet and Greet
- goatram
- Donator 08, 09, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19
- Posts: 1959
- Joined: Wed Apr 09, 2008 11:53 pm
- 16
- Your location: Stanwood, Wa
- Location: Stanwood WA
Re: The Journey Begins
The wiring has begun! Today Albert a electrician that works at Munson Boats in Anachortis is doing the wiring along with Dan also from Munson is helping. Dan is a friend of my son Jamie. Albert is Dan's lead. Albert is a Honda Certified Rigging Technician. Used to work at Care Toys Installing Car Stereos for 14 years. Hopefully he will ensure my boat is complaint to the latest ABYC Standards in prep for the Survey for the Insurance Coverage Requirements
4 bilge pumps; 2 ea. 2000 gph, 2ea. 1100 gph pumps with float and switch activations on each one. On the advice of some of my friends I am installing a diaphragm pump for the fish box. Will require a swap of discharge thru hull to a 1.5" pipe from 1 1/8". I was going with a Jabsco Macerater Pump The bait pump is a 1100 gph. The three underwater lights are installed. They are Ocean LED "Amphibians". Got them thru Ken aka Flasher at the Seattle Boat Show.
Glove box is welded up as is the dash. Need to start the layout. The radios; 2 each are going in an overhead removable panel. The 2ea. 2.5" half pipes previously installed were removed and will be replaced by 2ea. 1.5" pipes bent at the top that go into the fwd side of the overhead like what is on that cat by Armstrong at the boat show.
Hand rails are finished welded. The toe rails on the bow rail is being set in and welded at 3.5" off of the deck.
Brainstorming this past weekend might get me two dive doors one each side built like Munson's`current boats. They might make it on the boat prior to the engines and the eyebrows will be coming in the next couple of weeks too. Jim aka the welder said he can have both done in a weekend. He will work around the riggers.
4 bilge pumps; 2 ea. 2000 gph, 2ea. 1100 gph pumps with float and switch activations on each one. On the advice of some of my friends I am installing a diaphragm pump for the fish box. Will require a swap of discharge thru hull to a 1.5" pipe from 1 1/8". I was going with a Jabsco Macerater Pump The bait pump is a 1100 gph. The three underwater lights are installed. They are Ocean LED "Amphibians". Got them thru Ken aka Flasher at the Seattle Boat Show.
Glove box is welded up as is the dash. Need to start the layout. The radios; 2 each are going in an overhead removable panel. The 2ea. 2.5" half pipes previously installed were removed and will be replaced by 2ea. 1.5" pipes bent at the top that go into the fwd side of the overhead like what is on that cat by Armstrong at the boat show.
Hand rails are finished welded. The toe rails on the bow rail is being set in and welded at 3.5" off of the deck.
Brainstorming this past weekend might get me two dive doors one each side built like Munson's`current boats. They might make it on the boat prior to the engines and the eyebrows will be coming in the next couple of weeks too. Jim aka the welder said he can have both done in a weekend. He will work around the riggers.
- Attachments
-
- 1.5" SS thru hull, valve and manifold for the three pumps. the other valve is the drain for the fishbox. The 2000 GPH pump is in there too.
- 29'build151.pg.jpg (103.16 KiB) Viewed 10724 times
-
- Radar arch
- 29'build152.pg.jpg (117.01 KiB) Viewed 10724 times
-
- Toe rails were formed to match the upper rails.
- 29'build153.jpg (125.38 KiB) Viewed 10724 times
-
- Two pumps under the transom fishbox. Mounted on plastic cutting board
- 29'build154.jpg (86.16 KiB) Viewed 10724 times
-
- Starboard Mounted Washdown Pump and the Amidship Bilge Pump Discharge Thru Hull
- 29'build155.jpg (78.72 KiB) Viewed 10724 times
-
- Bare Dash as she will look minus the Glove Box Door and the helm
- 29'build156.jpg (92.68 KiB) Viewed 10724 times
-
- The Wiring Pipe port side. A 1" strip was welded to the inside seam of the fwd windscreen structure. the Pipe will be skip welded to it.
- 29'build157.jpg (72.25 KiB) Viewed 10724 times
-
- Center and Starboard underwater lights. Had to mount them like that due to the engine support structure in the swimstep
- 29'build157.jpg (72.25 KiB) Viewed 10724 times
John Risser aka goatram
33' RBW with twin 250 Hondas (Aliens)
2015 Ford F350 Dually
Master of R&D aka Ripoff and Duplicate
33' RBW with twin 250 Hondas (Aliens)
2015 Ford F350 Dually
Master of R&D aka Ripoff and Duplicate
- goatram
- Donator 08, 09, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19
- Posts: 1959
- Joined: Wed Apr 09, 2008 11:53 pm
- 16
- Your location: Stanwood, Wa
- Location: Stanwood WA
Re: The Journey Begins
Pete the Cuddy is 6.5" long and about 90" wide in the back but the frames make it smaller. Be sleeping in it Kaddywampas in it that is for sure. As June would say It is what it is
John Risser aka goatram
33' RBW with twin 250 Hondas (Aliens)
2015 Ford F350 Dually
Master of R&D aka Ripoff and Duplicate
33' RBW with twin 250 Hondas (Aliens)
2015 Ford F350 Dually
Master of R&D aka Ripoff and Duplicate
- Sabs28
- Donator '11 '12 '13 '14 '15
- Posts: 648
- Joined: Mon Mar 14, 2011 11:57 am
- 13
- Your location: Wits End
- Location: New Hampshire
Re: The Journey Begins
Looking GREAT John Why wood for the floor????
- goatram
- Donator 08, 09, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19
- Posts: 1959
- Joined: Wed Apr 09, 2008 11:53 pm
- 16
- Your location: Stanwood, Wa
- Location: Stanwood WA
Re: The Journey Begins
Cuddy Berth area Cabin Floor is .160" Aluminum.
Thanks Sabs for posting up and for the Question
Thanks Sabs for posting up and for the Question
John Risser aka goatram
33' RBW with twin 250 Hondas (Aliens)
2015 Ford F350 Dually
Master of R&D aka Ripoff and Duplicate
33' RBW with twin 250 Hondas (Aliens)
2015 Ford F350 Dually
Master of R&D aka Ripoff and Duplicate
- spoiled one
- Donator '08 '09 '10
- Posts: 1138
- Joined: Mon Jan 14, 2008 4:48 pm
- 16
- Your location: Anchorage, Alaska
- Location: Anchorage, Alaska
Re: The Journey Begins
That will work fine, especially if you are tired. Do you have room to hang cots in the berth like I did? It's hard to tell from the pics how tall it is in the stabbin' cabin'.goatram wrote:Pete the Cuddy is 6.5" long and about 90" wide in the back but the frames make it smaller. Be sleeping in it Kaddywampas in it that is for sure. As June would say It is what it is
Spending my kids inheritance with them, one adventure at a time.
2010 AK Meet & Greet
2012 AK Meet and Greet
2010 AK Meet & Greet
2012 AK Meet and Greet
-
- Donator '09
- Posts: 2246
- Joined: Sun Jan 13, 2008 12:19 am
- 16
- Your location: Seattle, WA
- Location: Seattle, WA
Re: The Journey Begins
John, I just went thru this with Jaimie (WATERDOG247) and his big Silver Streak, I can't get his rig into my lift, trailer is too wide. Can you measure yours, I have 9' 11" between my posts. Also your max height sitting on the trailer? I have 12' 5" there.
1987 24' LaConner pilothouse workboat, 225 Suzuki
please view and like: https://www.facebook.com/bottompainting/
please view and like: https://www.facebook.com/bottompainting/
- goatram
- Donator 08, 09, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19
- Posts: 1959
- Joined: Wed Apr 09, 2008 11:53 pm
- 16
- Your location: Stanwood, Wa
- Location: Stanwood WA
Re: The Journey Begins
I will measure it. Trailer I think is around 8'.6" Cabin is hopefully less than that 12'.5"
Will know soon enough
Will know soon enough
John Risser aka goatram
33' RBW with twin 250 Hondas (Aliens)
2015 Ford F350 Dually
Master of R&D aka Ripoff and Duplicate
33' RBW with twin 250 Hondas (Aliens)
2015 Ford F350 Dually
Master of R&D aka Ripoff and Duplicate
- waterdog247
- Donator '10, '12, '13
- Posts: 219
- Joined: Sat Aug 21, 2010 2:53 am
- 13
- Your location: Southern Philippines
Re: The Journey Begins
That is where i got into trouble. The top of the radar dome is 12' 6". The widest part of the boat isnt at the stern, its amid ship. The trailer is 8'6, but the gunnels and handrails push out 6" on either side. Just the slightest bit too big. (No ones ever told me that before!). :)goatram wrote:I will measure it. Trailer I think is around 8'.6" Cabin is hopefully less than that 12'.5"
Will know soon enough
- goatram
- Donator 08, 09, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19
- Posts: 1959
- Joined: Wed Apr 09, 2008 11:53 pm
- 16
- Your location: Stanwood, Wa
- Location: Stanwood WA
Re: The Journey Begins
You might have a point there Jamie, My rails are flared out a bit Trailer is 8' 6". I will attempt to measure it in the morning.
another update of the fast changing view
another update of the fast changing view
- Attachments
-
- my Bow rails from the Starboard side looking forward
- 29'build163.jpg (108.51 KiB) Viewed 10815 times
-
- my Bow with the bottom rung added
- 29'build164.jpg (114.85 KiB) Viewed 10815 times
-
- Radar Arch nearing completion
- 29'build165.jpg (113.37 KiB) Viewed 10815 times
John Risser aka goatram
33' RBW with twin 250 Hondas (Aliens)
2015 Ford F350 Dually
Master of R&D aka Ripoff and Duplicate
33' RBW with twin 250 Hondas (Aliens)
2015 Ford F350 Dually
Master of R&D aka Ripoff and Duplicate
- Sabs28
- Donator '11 '12 '13 '14 '15
- Posts: 648
- Joined: Mon Mar 14, 2011 11:57 am
- 13
- Your location: Wits End
- Location: New Hampshire
Re: The Journey Begins
Very Nice John Those bow rails look great.
- welder
- Site Admin
- Posts: 4668
- Joined: Thu Jan 03, 2008 11:51 pm
- 16
- Location: Whitesboro, Texas
- Contact:
Re: The Journey Begins
Toe rail looks good.
Did you sleeve the splice on the bow rail or just a but connection ?
Did you sleeve the splice on the bow rail or just a but connection ?
Lester,
PacificV2325, Honda BF225
2386
PacificV2325, Honda BF225
2386
- goatram
- Donator 08, 09, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19
- Posts: 1959
- Joined: Wed Apr 09, 2008 11:53 pm
- 16
- Your location: Stanwood, Wa
- Location: Stanwood WA
Re: The Journey Begins
Les BBQ Bob a machinest made the butt plugs to splice the tube. It helped alot cause I was setting and cutting by myself that day.
John Risser aka goatram
33' RBW with twin 250 Hondas (Aliens)
2015 Ford F350 Dually
Master of R&D aka Ripoff and Duplicate
33' RBW with twin 250 Hondas (Aliens)
2015 Ford F350 Dually
Master of R&D aka Ripoff and Duplicate
- goatram
- Donator 08, 09, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19
- Posts: 1959
- Joined: Wed Apr 09, 2008 11:53 pm
- 16
- Your location: Stanwood, Wa
- Location: Stanwood WA
Re: The Journey Begins
Ok the weekend is over, time for a report.
A lot was done some of which cant really see yet. First off is the two wire ways were welded in place at the front window dividers. They drop the wire into the overhead radio box. The two VHF radios the Lowrance Sonic Hub along withe the two 6.5" Lowrance speakers were install in the overhead. Holes were drilled at the radar support down tubes in prep to run wires to the roof. NAV lights are installed. Aft swim step and aft pumps are wired with the ends at the helm. The interior lights and back deck lights are going in.
Finally after three days of me leaving before the Fed Ex man made his atop I got my box of goodies from Defiance Marine. Ben in Parts for some reason shipped it with required signature. The helm can now be configured and parts made.
The back deck got some attention. First thing was the trays under the gunnel. The bottom one is set 3.5" up from the floor; this was done for safety. It will act as a toe kick. Only 6' was installed because this fall two dive doors will be installed one on each side of the boat. The pot puller davit was installed thru the gunnel on the starboard side. Made from schedule 80 2" pipe. Looks sweet.
My son TIGed all of the 34 rod holders. Ken says the standoffs should be done by Friday. Might get that done next week
More to come in my Epic Journey. I can feel it coming together.
A lot was done some of which cant really see yet. First off is the two wire ways were welded in place at the front window dividers. They drop the wire into the overhead radio box. The two VHF radios the Lowrance Sonic Hub along withe the two 6.5" Lowrance speakers were install in the overhead. Holes were drilled at the radar support down tubes in prep to run wires to the roof. NAV lights are installed. Aft swim step and aft pumps are wired with the ends at the helm. The interior lights and back deck lights are going in.
Finally after three days of me leaving before the Fed Ex man made his atop I got my box of goodies from Defiance Marine. Ben in Parts for some reason shipped it with required signature. The helm can now be configured and parts made.
The back deck got some attention. First thing was the trays under the gunnel. The bottom one is set 3.5" up from the floor; this was done for safety. It will act as a toe kick. Only 6' was installed because this fall two dive doors will be installed one on each side of the boat. The pot puller davit was installed thru the gunnel on the starboard side. Made from schedule 80 2" pipe. Looks sweet.
My son TIGed all of the 34 rod holders. Ken says the standoffs should be done by Friday. Might get that done next week
More to come in my Epic Journey. I can feel it coming together.
- Attachments
-
- running lights
- 29'build166.jpg (97.25 KiB) Viewed 10777 times
-
- 29'build167.jpg (110.32 KiB) Viewed 10777 times
-
- 29'build168.jpg (80.54 KiB) Viewed 10777 times
-
- Pipe wire ways
- 29'build169.jpg (90.01 KiB) Viewed 10777 times
-
- 29'build170.jpg (113.52 KiB) Viewed 10777 times
-
- 29'build171.jpg (95.74 KiB) Viewed 10777 times
-
- 29'build172.jpg (79.43 KiB) Viewed 10777 times
-
- my big foot stuck up under the tray
- 29'build173.jpg (88.3 KiB) Viewed 10777 times
-
- Pot pulling davit mount
- 29'build174.jpg (92.04 KiB) Viewed 10777 times
-
- 34 rod holders awaiting the 3/16" plate standoffs
- 29'build175.jpg (117.93 KiB) Viewed 10777 times
-
- 29'build176.jpg (86.37 KiB) Viewed 10777 times
John Risser aka goatram
33' RBW with twin 250 Hondas (Aliens)
2015 Ford F350 Dually
Master of R&D aka Ripoff and Duplicate
33' RBW with twin 250 Hondas (Aliens)
2015 Ford F350 Dually
Master of R&D aka Ripoff and Duplicate
- Sabs28
- Donator '11 '12 '13 '14 '15
- Posts: 648
- Joined: Mon Mar 14, 2011 11:57 am
- 13
- Your location: Wits End
- Location: New Hampshire
Re: The Journey Begins
Very nice welds John.
Now HURRY UP, Spring is here next week.
Now HURRY UP, Spring is here next week.