Search found 24 matches
- Tue May 25, 2010 8:59 pm
- Forum: Alloy Shop Talk
- Topic: How to post pic's in new topic
- Replies: 10
- Views: 6287
Re: How to post pic's in new topic
YEEEAAA, i Just kept trying the way IN2DEEP post #7 and i did it !!!! Finally . I probably forget tomorrow and just go back and read again.... Thanks Wayne
- Thu May 20, 2010 7:09 pm
- Forum: Alloy Shop Talk
- Topic: Where do you get these?
- Replies: 16
- Views: 8295
Re: Where do you get these?
Hey Nate ,,, this place has them on the west coast .. few years back were 3 bucks each . Give them a call
Riley Marine Products
840 W. Esther
Long Beach, CA 90813
Tel: (562) 435-5233
Fax: (562) 435-6512
Harbor/Locale: Alamitos Bay/Long Beach Marina
They will ship
Riley Marine Products
840 W. Esther
Long Beach, CA 90813
Tel: (562) 435-5233
Fax: (562) 435-6512
Harbor/Locale: Alamitos Bay/Long Beach Marina
They will ship
- Mon May 17, 2010 10:46 pm
- Forum: Alloy Shop Talk
- Topic: Practice welds
- Replies: 7
- Views: 4754
Re: Practice welds
Hi Kevin , Thanks for reply... ( Use more cover gas ? not sure of your flow now?) I am at 18 on my regulator ,pure argon What should i be at ?... I think I Was whipping my nozzle to much. I'll slow it down on next try. I tried preheating with mapp gas and i thought it welded a little easier ,Maybe i...
- Sun May 16, 2010 1:35 pm
- Forum: Alloy Shop Talk
- Topic: Practice welds
- Replies: 7
- Views: 4754
Re: Practice welds
Hey Kevin ,i added some pic's on post above rite before you posted ,,, what to u think ?
- Sun May 16, 2010 1:10 pm
- Forum: Alloy Shop Talk
- Topic: Practice welds
- Replies: 7
- Views: 4754
Re: Practice welds
Thanks Kevin ,, That is some Excellent information !!!! Would steel or aluminum be better for chillin bar or does it matter ? Also started Welding on boat , Horizontal stitches were working and they were getting wider but seems to hold together but now trying to do vertical on reinforcement to actua...
- Sun May 16, 2010 9:23 am
- Forum: Alloy Shop Talk
- Topic: Practice welds
- Replies: 7
- Views: 4754
Practice welds
Good morning Guys,, Did some practice welds before welding on tinny...Had a few questions about welds cracking as i welded. Lowered settings as i went. Started on far right and left side was last and was at lowest heat setting my welder will go . Going to try and post pics and back side showing pene...
- Sat May 15, 2010 9:12 pm
- Forum: Alloy Shop Talk
- Topic: How to post pic's in new topic
- Replies: 10
- Views: 6287
Re: How to post pic's in new topic
This is like beating a dead horse ,, and i'm the fricken horse... cant figure how to send pics from photobuc to alloyboat... wouldn't it be one less step just uploading to alloy site ?? Is there a tutorial for that ? I think i need to get my other fishin bud/ computer guru on to this site ,let him l...
- Fri May 14, 2010 11:09 pm
- Forum: Alloy Shop Talk
- Topic: How to post pic's in new topic
- Replies: 10
- Views: 6287
Re: How to post pic's in new topic
Well i'm registered and logged in on Photobucket but just not understanding where to go after ,, Read instructions on other topic page but still lost. Not gettin how to get to Browse button Daddy'o I''ll try again tomorrow ...
- Fri May 14, 2010 10:48 pm
- Forum: Alloy Shop Talk
- Topic: How to post pic's in new topic
- Replies: 10
- Views: 6287
Re: How to post pic's in new topic
Help ,,, I looking for some Help from MODERATOR Please .. I'm Lost . I've Fallen and i can't get Up........how to post pic in new post ????
- Fri May 14, 2010 10:41 pm
- Forum: Alloy Shop Talk
- Topic: How to post pic's in new topic
- Replies: 10
- Views: 6287
Re: How to post pic's in new topic
click post reply on the bottom of the page to the left you will see "upload attachment" Yea , that's what i tried before ,kinda like sending a email and a attachment ,But not the same. Hitting browse does nothing ....HIT add a file and page blinks but not noticing anything different ....S...
- Fri May 14, 2010 4:46 pm
- Forum: Alloy Shop Talk
- Topic: How to post pic's in new topic
- Replies: 10
- Views: 6287
How to post pic's in new topic
Hey guys ,, Can someone tell me or direct me to a tutorial page on how to put pics on posts when starting a new topic... I'm confused on Img and url buttons above where you write ..Thanks Wayne
- Sat Apr 24, 2010 9:08 pm
- Forum: Alloy Boat Forum
- Topic: Construction Methods for Pacific Boats build
- Replies: 24
- Views: 10461
Re: Construction Methods for Pacific Boats build
heck yes I would like to see a step by step build thread, I really want to see the bilge and stingers, fuel tank, plumbing and rigging chases before the floor goes on ! and a video of the foam going in ! :thumbsup: :thumbsup: :thumbsup: ME TOO...VERY INTERESTING ... THESE BOATS ARE PIECES OF ART !!...
- Wed Apr 14, 2010 11:20 pm
- Forum: Alloy Boat Forum
- Topic: Construction Methods for Pacific Boats build
- Replies: 24
- Views: 10461
Re: Construction Methods for Pacific Boats build
GREAT PIC'S !!! I WANNA SEE MORE , !!!! Beautiful work .... Keep them coming !!
- Sat Apr 10, 2010 3:27 pm
- Forum: Alloy Shop Talk
- Topic: Another aluminum mig welding question
- Replies: 14
- Views: 9729
Re: Another aluminum mig welding question
Kevin ,, first clean with water, boats a bit dusty from sitting.Or should i just blow off Then Acetone then wire wheel with fine bristles.. so your saying tooth brush without out acetone ,Just dry ? Rite before i start welding ? Wayne
- Sat Apr 10, 2010 1:10 pm
- Forum: Alloy Shop Talk
- Topic: Another aluminum mig welding question
- Replies: 14
- Views: 9729
Re: Another aluminum mig welding question
Hi Kevin,, Do YOU think my power supply [ sp-130t ] 220 unit is not going to be enough to heat? Should i preheat the aluminum [ 18 gauge some is a little thicker] . And should i also clean with acetone after SS wire brushing area to be welded ? ... It's over cast now , maybe should wait for sunny da...
- Fri Apr 09, 2010 9:47 pm
- Forum: Alloy Shop Talk
- Topic: Another aluminum mig welding question
- Replies: 14
- Views: 9729
Re: Another aluminum mig welding question
Hi Guys, picked up my .035 1 lb spool of 5356 . with some new tips.Made it to Airgas , Salesmen said going thicker would help with pushing wire through . I believe one of you guys said to go thicker also. I will get back with results soon ,hopefully this weekend i'll get some free time to mess aroun...
- Sun Apr 04, 2010 1:27 pm
- Forum: Alloy Shop Talk
- Topic: Another aluminum mig welding question
- Replies: 14
- Views: 9729
Another aluminum mig welding question
Happy Easter Everyone ! I want to pick your guys' brains some more.. Was told to use 5356 , ,,only found 4043 or 4047 at Lowes yesterday ..Welderbob or Kmorin you out there ? Whats' the different between spools of superglaze and just regular aluminum welding wire.. ? Can i use 4043 or 4047 or do i n...
- Sat Apr 03, 2010 9:09 am
- Forum: Alloy Shop Talk
- Topic: what aluminum wire should i purchase
- Replies: 6
- Views: 4102
Re: what aluminum wire should i purchase
Welderbob, yea i tried that search everywhere in my and surrounding area .No one rent's around here .I already have a bottle of argon . Actually welded stainless with my machine before , not as pretty as a tig weld but i didn't have much to weld ,so it worked out. Need to price this stuff today or n...
- Fri Apr 02, 2010 8:49 pm
- Forum: Alloy Shop Talk
- Topic: what aluminum wire should i purchase
- Replies: 6
- Views: 4102
Re: what aluminum wire should i purchase
Hi Guys ,, Thanks for replies so quick. I made a mistake on model number it's a SP-130T 220 UNIT. probably doesn't matter . But i hear yea it might be a pain in BACK SIDE . But the welds do not need to look pretty anyways .The welds look like fricken bubble gum from the factory. So your saying go wi...
- Thu Apr 01, 2010 9:10 pm
- Forum: Alloy Shop Talk
- Topic: what aluminum wire should i purchase
- Replies: 6
- Views: 4102
what aluminum wire should i purchase
Hi Guys , I am going to attempt fixing some cracks on my 84 Westcoaster tinny and would like to know which wire to use in my Lincoln SP-130t ,this unit is the early 220 unit. I plan on getting a teflon or plastic liner ,possibly different drive rollers " think i read somewhere to use U groove d...
- Sat Mar 27, 2010 10:50 pm
- Forum: Your Alloy Boat
- Topic: AMF 660 Hardtop Cabin -Western Australia Boat review
- Replies: 6
- Views: 5634
Re: AMF 660 Hardtop Cabin -Western Australia Boat review
I'm CURIOUS ,,When welding up the reverse chine in the pic..Are you guys preheating that material to bend as welded or what's the method and what grade aluminum if you don't mind me asking ...Thanks Wayne
- Sat Mar 06, 2010 3:54 pm
- Forum: Share your Projects and Creations
- Topic: Adding a cockpit helm station
- Replies: 20
- Views: 12601
Re: Adding a cockpit helm station
Hey Capt. where can i find a used 'LaConner Boat like that,, SWEET !!
- Sun Sep 06, 2009 8:36 pm
- Forum: Aluminum Boats For Sale
- Topic: 23' welded aluminum boat. A good find ?
- Replies: 10
- Views: 7066
Re: 23' welded aluminum boat. A good find ?
WELL LET'S SEE SOME PICTURES DUDE !!!! DON'T KEEP US WAITING .....SSSSHHHHHEEEEEEEESSSSHHHHHpjay9 wrote:Clist listing is GONE!! what happened? Capt PJ :-?
- Tue Jan 13, 2009 9:38 pm
- Forum: Electronics
- Topic: Fish finders in different languages
- Replies: 4
- Views: 4206
Fish finders in different languages
Does any of the top FF companies sell units in Vietnamese.... You know a different language other than english that comes over the screen ? Am i making sense ? Thanks in advance...Wayne ...